Most common steam iron problems and their solutions

steam iron problems
Image Credits: Pexels

Steam iron is one of the most useful electronic appliances and is owned by almost everyone. The appliance enables us to steam iron our clothes so that they look fresh and crisp when we wear them. However since this appliance is used so often it can develop certain problems from time to time. But before you take a decision on how to solve these problems, you must know what they are and be prepared for them. This article will help you learn about the most common steam iron problems and their respective solutions:

1. Mineral build-up

This is one of the most common steam iron problems and can lead to decreasing the life expectancy of your appliance. What happens is that the water that you use in it may be hard and can contain certain minerals which may deposit in the lines and vents of your iron.  These may then block the discharge of the steam coming from the iron and may lead to dripping. To avoid this, use distilled or filtered water only and one used, empty the water from the tank.  To clean the build-up, you can make use of a commercial cleaner for lime or calcium removal.

2. Spotting

Another common steam iron problem that you can counter is the problem of spotting.  If your steam iron is overfilled, then it will leave a stream of water from the ports which the appliance is in its position to be used.  The water that drips or falls can lead to water spots on the clothes which may appear bad.  The best solution for this problem is to avoid filling the iron to the top and leave some room. Stop before you reach the maximum recommended level.

3. Iron not heating

You may have also come across the issue of the steam iron not heating. This is yet another very common steam iron problem. To check the cause of this issue, you must first ensure that the power cord is properly connected and switched on.  Next check the electrical cord and the thermostat. Correct the thermostat setting and check the heating again.  If it is not working properly, then this could be an issue and the cause of iron not heating. Get it replaced by contacting a professional electrician.

Our Pick

4. Iron sticks to fabric

A lot of people have also experienced the situation when the steam iron sticks to the fabric.  In this case, the issue may be with the soleplate.  The first thing you need to do is to clean the soleplate.  Clean the tank by making use of a commercial cleaner and make sure you use only distilled water for this. However if the problem persists, the soleplate may be faulty and you may have to get it replaced.

iron sticking to fabric
Image Credits: Wikimedia Commons

Now that you know the most common steam iron problems and their solutions, you too can figure out the cause yourself. If there is need for any steam iron problems or iron not working, you can contact Mr Right. Also, you can check the Kitchen Home guide on the best steam generator irons.

You might also like


  1. 1

    The norm of impact can be controlled in different circles of life and is habitually utilized in cash to convey the connection among responsibility and worth. Use the norm of impact, particularly self-progress, ISO Consultants in basra to raise yourself to the supporting level if you have any desire to be heard in the ongoing tumultuous world since you can’t clinician to significance.

  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8

    Hi i have brand new one week old tefal express compact iron, I’ve just switched it on and all the lights are flashing, the on button, anti calc, eco and vertical steam are all just flashing. What do I do.

  9. 9
  10. 10
  11. 11

    My iron switches on the light comes on( it’s a swan model) but my iron won’t warm up what vould ne the problem?

  12. 12

    Mr Right I recently dropped my iron as it was sitting upright on the ironing g board. I hit a set of metal bed rails I had stored against the wall u underneath the board itself. The iron works perfectly but it now has 2 tiny pieces of metal that broke off. The 2 pieces of metal are located at the top of the iron. When I iron something, these 2 pieces of metal that have 1 sent each, catcheson the fabric of the piece I am ironing. It snags on every fabric. I cannot use my iron to press my good clothes. Please tell me what to do? Wondering if I can file down the 2 pieces that snag e erytjinh I iron?

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>